plane inclination
英 [pleɪn ˌɪnklɪˈneɪʃn]
美 [pleɪn ˌɪnklɪˈneɪʃn]
网络 平面式植入物
双语例句
- Objective To evaluate the validity of the pelvic anterior plane ( PAP) as the reference plane for acetabular component implantation by analyzing the change of the pelvis inclination between the supine and standing positions.
目的分析卧位和站立位时骨盆倾斜度的变化情况，观察骨盆前平面作为髋臼假体植入的参照平面时的稳定性。 - Fraunhofer diffraction pattern of the plane wave inclination incidence
平面波倾斜入射时的夫琅和费衍射花样 - A LINE OF MAXIMUM INCLINATION AND A PLANE OF MAXIMUM INCLINATION Discussion on the mechanical structure, Principles and ways of control for three dimensional WEDM
斜度线切割结构、控制原理和方式的讨论 - Diffraction and reflection of a plane shock wave passing a mountain of 30 ° inclination
平面激波绕30°出峰后的绕射与反射 - Stresses and Deformations of Dam Foundations With Structural Plane of Gentle Inclination Study on the Equal K Design Method for the Gentle Sloping Fissure Strengthened by Shear Keys at Gravity Dam Foundations
混凝土硐塞加固重力坝基缓倾角结构面等K设计方法研究 - Results: ( 1) The inclination of occlusion plane, mandibular plane and the curve of cervical vertebrae were all higher in mandibular deviation patients than those in normal occlusion persons. But the cervical vertebrae inclination was smaller in the patients.
结果：①下颌偏斜者咬合平面、下颌平面的陡度及颈椎弯曲度大于正常咬合者而颈椎倾斜度小于对照组，患者头呈前倾位； - In this paper, the plane inclination and non-plane inclination of the surface and deep soil, and the sway settlement of the round wall are discussed.
论述了地基地表土、深层土、油罐地基的平面倾斜与非平面倾斜及环墙摇摆下沉特性； - The angle represented by Frankfort horizontal plane to mandibular plane was associated with tooth and bone inclination of the Ml section.
第一磨牙的牙倾斜度、骨倾斜度与面型参数有相关性。 - A horizontal attitude sensor, which can measure the inclination in any direction from 0 °~ 360 ° in horizontal plane, is introduced. This sensor can output an alarming signal when the inclination angle exceeds 10 °.
本文介绍了一种能够在水平面的0°～360°范围内任意方向敏感角度变化，并可在倾斜角大于10°时给出报警信号的全方位水平姿态传感器。 - Conclusion: The UCLP subjects presented a significant increase in extension of the head relative to the vertical plane and backward inclination of the first vertebra comparing with the malocclusions without cleft.
结论：与无唇腭裂的错（牙合）患者相比，UCLP的患者的头位相对于垂直平面更伸展，第一颈椎更后倾。 - This paper describes experimental study and analysis of diffraction and reflection of a plane shock wave passing a mountain of 30 ° inclination.
本文针对一平面激波S绕过坡角为30°的山峰后与地面作用所产生的波系图案等问题，通过激波管光测模型实验手段进行了分析和研究。 - It is advanced that the method determins the occurrence of rock mass plane using analytical geometry method, by three-shot boreholes inclination survey data and core structural plane rake.
文章提出了采用立体解析几何法，依据3点钻孔测斜资料、岩芯层面角，确定岩体结构面产状的方法。 - So all of the plane problems in description geometry can be solved through the normal plane system with the normal footmark, the intersection point of normal and maximum inclination line.
通过法线的法足、法迹和最大斜度线的线迹，使画法几何中有关平面的问题在法线平面体系中均可得到解决。 - Calculation of Global Solar Radiation on Inclined Plane in Different Inclination Angles
变倾角倾斜面上太阳辐射总量的气候学计算 - Inquisition into the Plane Double Enveloping Worm Gear of Changing the Inclination β
变倾角β式平面二次包络弧面蜗杆传动探讨 - It introduces the perspective system feature in different positions between tableau and datum plane inclination.
研究了画面与基面处于不同位置时的透视体系特征。 - In seismic prospecting, the 3-D ray tracing for plane reflectors with arbitrary inclination is a forward problem.
任意倾斜平界面三维射线追踪，是地震勘探工作的正问题。 - All studies show that weak plane inclination, thickness and whether be run through or not have a significant impact on longitudinal wave velocity, average modulus and strength of specimens.
研究结果表明：弱面的倾角、厚度及是否贯通等对试样的纵波速度、平均模量和强度具有显著的影响。 - The influence of the cohesive strength, friction angle of the weak joint plane and the inclination of the rock slope on the stability is studied.
同时，分析了软弱结构面的粘聚力、摩擦角和岩层倾角对该类边坡的稳定性的影响。 - Based on the simulation model of plane topography, the effects of initial entrance angle, spindle rotational eccentricity, machining inclination angle, radial depth of cut, the feed per tooth and tool wear on surface topography were studied in this paper.
基于平面形貌仿真模型，研究了初始切入角、回转偏心、加工倾角、径向切削深度和每齿进给量等几何因素以及刀具磨损对表面形貌的影响。